Just how to Replace a Bathtub ( Guide).
Just how to Replace a Bathtub ( Guide).
Blog Article
We've found this great article about A Step-by-Step Guide to Installing a Bathtub down the page on the net and concluded it made sense to write about it with you here.
Installing a bath tub isn't specifically rocket science, but it does call for solid plumbing, carpentry, and also in some cases, tiling abilities. Changing an old bathtub with a brand-new one is likewise a moderately tough job. If the old tub is conveniently available, the project can relocate quickly; if you need to open a wall surface to eliminate the old tub and also position the brand-new tub, the task is a lot harder. In either case, the task is within a house handyman's abilities, although you will certainly require a helper to leave the old tub and also set in the brand-new one. Ensure you have actually qualified on your own for the task and also are comfortable trying it. Instead of hiring a specialist to take control of a halfway-completed job, it is far better to think about using one before you start. Possibilities are you might need a specialist plumber to make tube connections.
This post will certainly help you set up a brand-new bathtub in your washroom if you have currently bought a new bathtub and do not need to alter the setup of your previous supply of water pipes.
Your devices and product list ought to consist of the following:
Planning for the Installation
First of all, the sustaining frame provided with the bathroom should be fitted (if needed) according to the supplier's instructions. Next, fit the faucets or mixer to the bath tub. When fitting the tap block, it is necessary to ensure that if the faucet comes with a plastic washing machine, it is fitted in between the bath as well as the faucets. On a plastic bath, it is likewise sensible to fit a supporting plate under the faucets device to prevent pressure on the bathtub.
Fit the versatile faucet connectors to the bottom of the two faucets making use of 2 nuts and olives (often provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet via the hole in the bath. Utilize the nut provided by the manufacturer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the versatile overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which must be fitted inside the bathroom. Make sure you use all of the provided washing machines.
Connect the trap to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect the bottom of the overflow tube in a similar manner.The bathroom need to currently be ready to be fitted in its final setting.
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your installation, then the first thing you ought to do is detach the water system. After doing so, activate the faucets to drain pipes any kind of water remaining in the system. The process of eliminating the existing faucets can be quite problematic due to the restricted access that is typically the case.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipes to the taps. Have a cloth ready for the staying water that will come from the pipes. Once the supply pipes have been removed, use the same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the single taps from turning during this process. As soon as the faucets have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleaned up of any type of old sealing compound.
Prior to going on to fit the brand-new faucets, contrast the pipe connections on the old taps to the brand-new faucets. If the old faucets are longer than the brand-new taps, then a shank adapter is required for the brand-new faucets to fit.
Setting up the Tub
Using the two wood boards under its feet, position the tub in the needed position. The wood boards are handy in uniformly spreading the weight of the bathtub over the location of the boards as opposed to focusing all the weight onto four small factors.
The following goal is to ensure that the bath tub is leveled all round. This can be achieved by checking the level as well as adjusting the feet on the bathtub till the spirit level reads degree.
To set up taps, fit the bottom of the furthest flexible faucet connector to the ideal supply pipe by making a compression sign up with; then do the very same for the various other tap.
Turn on the water supply and also check all joints and also new pipework for leakages and tighten them if essential. Fill up the bath tub and additionally inspect the overflow electrical outlet as well as the regular outlet for leakages.
Finally, deal with the bath paneling as explained in the manufacturer's instruction manual. Tiling and also sealing around the bath tub should wait up until the bathtub has been made use of a minimum of when as this will certainly settle it right into its last setting.
Suitable New Taps
If the tails of the brand-new faucets are plastic, then you will certainly require a plastic port to stop damage to the string. One end of the port fits on the plastic tail of the faucet as well as the various other end offers a link to the existent supply pipelines.
If you need to fit a monobloc, after that you will need reducing couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next, place the tap in the installing opening in the bath/basin guaranteeing that the washing machines are in location in between the tap and also the sink. Secure the faucet in position with the producer supplied backnut. Once the tap is firmly in place, the supply pipes can be attached to the tails of the taps. The taps can either be attached by using corrugated copper piping or with typical tap adapters. The former type must be connected to the tap finishes initially, tightening just by hand. The supply pipelines can later be linked to the various other end. Tighten up both ends with a spanner after both ends have been connected.
Tiling Around the Tub
In the location where the bath satisfies the ceramic tile, it is essential to seal the joins with a silicone rubber caulking. This is very important as the installation can move enough to split an inflexible seal, causing the water to permeate the wall surface in between the bathroom and the tiling, resulting in issues with wetness and possible leaks to the ceiling below.
You can pick from a range of coloured sealers to assimilate your fixtures as well as fittings. They are offered in tubes as well as cartridges, as well as can sealing spaces as much as a width of 3mm (1/8 inch). If you have a larger space to fill up, you can load it with spins of soaked newspaper or soft rope. Remember to always fill up the tub with water prior to sealing, to enable the motion experienced when the bathtub remains in usage. The sealer can fracture rather very early if you do not take into account this movement before sealing.
Alternatively, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are also easily available on the market. It is advisable to fit the floor tiles utilizing waterproof or water resistant sticky as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We were guided to that write-up on Installing A Bathtub from an acquaintance on another web property. Are you aware of someone else who is in the market for Installing A Bathtub? Take a moment to share it. Thanks a lot for taking the time to read it.
Check This Out Report this page